The Manual-to-Electric Conversion Kit for HappiJac Truck Camper Jack Systems Item # LC733960-182524 has everything you need to convert to electric jacks and will not require any special tools to install. view full answer...
For an 18 foot Carefree electric awning, you do have the right part with the Solera Family Room for 18' RV Awning # LC362233.
There are no other parts you need to purchase in order to install it, but you will need some very basic tools for the installation. According to the instructions - which I have linked for you - the tools needed are simply a cordless drill, mallet/hammer, 1/4” hex head bit, measuring tape, sealant, and ladder. Once you have all that you're all set! view full answer...
We have two options for a replacement crank for an electric A-frame jack, but no way of knowing what jack you have on your trailer, so you'll need to know that to get the right replacement.
We have the Replacement Manual Jack Handle for etrailer or RAM Electric A-Frame Jack # EJ-3520-HD and the Replacement Manual Crank Handle for Stromberg Carlson Electric Trailer Jacks # SC94VR. view full answer...
While we don't carry a replacement manual crank for the Ultra Fab Trailer jack part # UF38-944037 all you need is a 9/16 inch deep well socket as that's what the included tool is. view full answer...
Yes, the K-Source Custom Extendable Towing Mirrors - Electric/Heat w LED Signal # KS62093-94G will work with your 2013 GMC Sierra that doesn't have the heated mirror or signal option. Some customers have choose to run a auxiliary wire to operate the turn signal feature as well. Please note that if you use the mirror curb assist feature when backing up that feature will no longer work.
You will benefit greatly by using a Trim Panel Tool # ALL648544 as there are a lot of retention fasteners... view full answer...
I spoke with some of the manufacturers that make flat towing parts and they said that since Ford does not allow flat towing on the 2020 or 2021 Ford Explorer, they will not be making base plate kits for them.
If your Explorer is front wheel drive you could use a towing dolly like the Roadmaster # RM-2050-1 tow dolly with electric brakes. This dolly features easy drive-on loading.
The dolly comes with an attached flat 4-pole connector installed and a loose wire for the brakes if needed... view full answer...
Dutton-Lainson states:
"Special care should be taken with 120-volt AC winches, as with any other 120-volt tools. It is recommended that whenever a 120-volt AC winch is out-of-doors that it be used with a ground fault circuit interrupter (GFI outlet)."
It goes on to say not to use it in the rain or if it is wet. They also state that the winch is great for watercraft lifts. So provided the winch is not getting wet it will work great for your application. this is going to pretty much be... view full answer...
There is a way to manually retract the jacks on your Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System # LC358590.
I have cut out a portion of the directions which goes over what you need to do:
Top of Jack Motor Override:
Tools needed:3/8” drive ratchet and extension (no socket)
1. Find the port on the top of the jack motor
2. Remove the rubber plug
3. Insert the 3/8” drive into the port
4. Turn override until the jack extends or retracts to desired position.
Bottom... view full answer...
It sounds like you are looking for towing mirrors that will replace the current mirrors that you have on your 2016 Chevrolet Express Van. If that is the case then the K-Source Custom Towing Mirrors # KS62169-70G are the only full replacement towing mirrors that we have that fit your 2016 Chevrolet Express Van. But, these are manual mirrors, not electric.
You do have another option though, and that would be a slip-on mirror. For that I would recommend the Longview Custom Towing Mirrors... view full answer...
My contact at Pop and Lock advises that their Manual Tailgate Lock, part # PAL3400, will fit your 2004 Dodge Ram 3500 Pickup. This armored steel lock mechanism installs using the OEM tailgate handle.
It comes complete with 2 keys and requires no drilling for installation, only basic hand tools. view full answer...
The correct brakes and hubs/drums for a Dexter E-Z Lube 3,500 Lb Axle is the Dexter Nev-R-Adjust Electric Trailer Brake Kit part # 23-468-469 and Dexter Trailer Hub and Drum Assembly part # 84546UC3-EZ. view full answer...
For a driver's side swing-away arm for your Hollywood Racks Sport Rider SE Bike Rack for 2 Electric Bikes # HLY84FR we have the Kuat Pivot 2 Swing Away Hitch Extender for Bike Racks # PVD20B. It has a weight capacity of 250lbs and is only rated for use on cars, SUVs, vans, and trucks so you won't be able to use it on a trailer with a 2" hitch receiver. It is a tool-free installation in your hitch with hand-tightening cam system and has a toggle clamp that lets you quickly release latch... view full answer...
Unlike some of the other powered a-frame jacks the Electric Jack w/ Footplate # EJ-3520-BBX that you referenced does not come with a limiter at the top or bottom of its range. Greasing the inner jack leg once a year like you mentioned would be a great maintenance schedule for this jack although it doesn't have one specified. The height of this jack above the trailer frame it attaches to is 20-1/2 inches which you can compare that measurement to your tailgate area to determine if this would... view full answer...
It is necessary that your vehicle OEM mirrors already have these same functions (power adjustment, heat and turn signals) in order to have them work with the K-Source mirrors. The K-Source mirrors connect using the vehicle OEM wiring harness (please see included photo of the mirror connector). This wiring has to already have the capability of delivering the required 12V power and turn signals. These functions will not work unless the OEM mirrors have these same functions already, or unless... view full answer...
I spoke with my contact at Pop and Lock and she informed me that yes, the Pop & Lock Custom Tailgate Lock, part # PAL8521, will work with the integrated back up camera that is in the tail gate of your 2011 Toyota Tacoma.
There is not any drilling required to install the Pop & Lock Custom Tailgate Lock, part # PAL8521, and can be installed with basic tools. The Custom Tailgate Lock, part # PAL8521, includes a 1-year warranty. view full answer...
Yes the Redarc Tow-Pro Elite Trailer Brake Controller # RED44FR is compatible with electric over hydraulic braking systems on up to 3 axles. So it will work with the installation of the HydraStar Disc Brake Kit w/ Actuator for Triple Axle Trailers # HSE7K-TR1.
By upgrading to the hydraulic disc brake kit this will greatly increase the amount of stopping force that your 2019 Dutchman Voltage Epic 3970 will have. You will not need a more powerful brake controller as the Redarc will be all... view full answer...
Yes, the K-Source Custom Snap-On Towing Mirrors, part # KS80800, will fit your 2004 GMC Yukon XL Denali with either heated electric mirrors or manual mirrors. It will not fit on OEM extendable mirrors, OEM full chrome mirrors, or telescoping mirrors.
These K-Source towing mirrors snap into place on your stock mirrors without tools and can be removed quickly for parking in tight spaces. They do not interfere with your adjustments to the factory mirror.
I have linked a video showing installation... view full answer...
The A-iPower 5,000-Watt Portable Generator, Item # 289-AP5000, is designed to power appliances and tools like air compressors, air conditioners, electric heaters, etc. To choose the right generator, you must match the size of the generator (starting output and running output in watts) with the electrical demands of the appliances or equipment you will be operating. The A-iPower Generator has a starting (surge) power output of 5,000 watts and a running (rated) power output of 4,000 watts... view full answer...
Yes, the Dexter Electric Trailer Brake Assembly # 23-181 must be oriented so the brake shoe pin is at the top and the adjusters are at the bottom. This is also only for mounting on the right side of your axle. We have the Assembly # 23-180 for the left. I recommend upgrading to the Self-Adjusting Brakes # AKEBRK-7-SA. These will replace your current 12" Dexter brakes and will self adjust as they wear down. There is no need to try and adjust them with the Adjustment Tool # 071-666-00 every... view full answer...
Due to the threaded design of the hitch pin/hitch receiver tube you won't be able to use a standard hitch pin. It does take longer to remove the hitch pin from the Yakima OnRamp Bike Rack for 2 Electric Bikes # Y36FR but the benefit of no rattling while hauling your bikes around will outweigh the extra time it takes. The anti-rattle hitch pin also acts as a theft deterrent as well as it will take longer for any potential thieves to try and steal your rack and will require tools to remove.... view full answer...
Go To Results